Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
- 3. Maintenance service
- 3.1. Maintenance service of cars with petrol engines
3.1.1. Operational materials and liquids
3.1.2. Refuelling capacities
- 3.1.3. Periodicity of service
- 3.1.3.1. Each 15 000 km
3.1.3.1.1. Replacement of oil and the oil filter
3.1.3.1.2. Replacement of spark plugs
3.1.3.1.3. Check of tightness of hoses and вытекания liquids
3.1.3.1.4. Check and replacement auxiliary drivers belts
3.1.3.1.5. Check of system of ignition
3.1.3.1.6. Adjustment of turns of idling and quality of a mix
3.1.3.1.7. Clearing of the filter of the fuel pump on models with the carburettor
3.1.3.1.8. Level check трансмиссионной liquids
3.1.3.1.9. Check of a condition of oil
3.1.3.1.10. Electroconducting check
3.1.3.1.11. Check brake колодок and a brake disk
3.1.3.1.12. Adjustment of a manual brake
3.1.3.1.13. Exhaust system check
+ 3.1.3.2. Each 30 000 km
+ 3.1.3.3. Each two years
+ 3.1.3.4. Each 60 000 km
+ 3.2. Maintenance service of cars with diesel engines
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes
|
ПРИВОДНОЙ THE GENERATOR BELT
Term of its service depends on a correct tension auxiliary drive a belt. However do not draw auxiliary приводной a belt as generator bearings in this case can fail.
Check and adjustment
| PERFORMANCE ORDER |
| 1. Check of a condition of a belt make on all its length. In the presence of deterioration, разлохмачивания or cracks it is necessary to replace a belt. It is desirable to have in the car spare приводной a belt of corresponding type. |
| 2. The belt tension is considered correct if by pressing by a hand thumb the middle of the longest branch of a belt the belt deflection makes 13 mm. |
| 3. For adjustment ослабьте the top nut of fastening of the generator and a bolt of fastening of an arm. Using wooden брусок, wring out the generator from the engine and adjust a tension auxiliary drive a belt. After tension adjustment tighten the top nut of fastening of the generator and a bolt of fastening of an arm. |
|
Replacement
| PERFORMANCE ORDER |
| 1. Loosen the a nut of the top fastening of the generator and a bolt, крепящий an arm, then, moving the generator to the engine, ослабьте a tension auxiliary drive a belt also remove it from pulleys. On models with the steering amplifier first of all it is necessary to remove приводной a belt of the pump of the amplifier of a steering. |
| 2. Establish auxiliary приводной a belt on pulleys and adjust its tension. At installation of a new auxiliary belt repeatedly adjust its tension in 5 minutes of work of the engine. |
|
ПРИВОДНОЙ THE BELT OF THE PUMP OF THE AMPLIFIER OF THE STEERING
Term of its service depends on a correct tension auxiliary drive a belt. However do not draw auxiliary приводной a belt as generator bearings in this case can fail.
Check and adjustment
| PERFORMANCE ORDER |
| 1. Check of a condition of a belt make on all its length. In the presence of deterioration, разлохмачивания or cracks it is necessary to replace a belt. It is desirable to have in the car spare приводной a belt of corresponding type. |
| 2. The belt tension is considered correct if by pressing by a hand thumb the middle of the longest branch of a belt the belt deflection makes 13 mm. |
| 3. For adjustment of a tension of a belt ослабьте the counternut of an adjusting bolt located on the basis of the pump, and, rotating a regulator nut, adjust a belt tension. Tighten a counternut. |
|
Replacement
| PERFORMANCE ORDER |
| 1. Loosen the a counternut, then completely unscrew an adjusting nut and remove приводной a belt from pulleys. |
| 2. Establish auxiliary приводной a belt and adjust its tension. At installation of a new auxiliary belt repeatedly adjust its tension after 5 minutes of work of the engine. |
|
ПРИВОДНОЙ THE BELT OF THE PUMP OF THE AMPLIFIER OF STEERING MANAGEMENT / OF THE GENERATOR ON LATE MODELS 1,6 OF L
Since March, 1987 one belt for a drive of the generator and the pump of the amplifier of a steering on engines of 1,6 l is used. Used flat приводной the belt with ribs has higher tension.
For adjustment of a tension auxiliary drive a belt it is necessary to use an adapter.
Use of adapter КМ-612 for adjustment of a tension auxiliary drive a belt on late models with engines of 1,6 l
Check and adjustment
| PERFORMANCE ORDER |
| 1. Loosen the a point of turn of the generator and adjusting bolts of a belt also establish an adapter. |
| 2. Using динамометрический a key, tighten an adjusting bolt the moment of 55 Nanometers for a new belt or 50 Nanometers for a belt which was in the use. |
| 3. Keeping a belt in this position, tighten bolts of fastening of the generator. |
|
Replacement
| PERFORMANCE ORDER |
| 1. For belt removal ослабьте a point of turn of the generator and bolts also remove приводной a belt from pulleys. |
| 2. Establish приводной a belt and adjust its tension. At installation of a new wire belt repeatedly adjust its tension after 5 minutes of work of the engine. |
|
|
|
