Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
- 8. Ignition system
   + 8.1. System of ignition with the breaker
   - 8.2. Electronic contactless system of ignition
      8.2.1. A technical characteristics
      8.2.2. Check of system of ignition
      - 8.2.3. The ignition distributor
         8.2.3.1. Removal of the distributor of ignition
         8.2.3.2. Installation of the distributor of ignition
         8.2.3.3. Repair of the distributor of ignition
      8.2.4. Adjustment of a corner of an advancing of ignition
      8.2.5. Removal, check and installation of the coil of ignition
      8.2.6. Removal and installation of the block of ignition (switchboard)
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes


944881c0

8.2.3.2. Installation of the distributor of ignition

MODELS 1,3 AND 1,4 L WITH THE CARBURETTOR

PERFORMANCE ORDER
1. Check up that the cranked shaft of the engine was not turned after removal of the distributor of ignition. Otherwise return a cranked shaft in a starting position.
2. Turn the ignition distributor so that contact of a rotor of the distributor was combined with an arrow or a label on the case of the distributor of ignition.
3. In this position ledges on муфте (drawing at the left) a drive of the distributor of ignition will be established in position at which they will be established in a groove (drawing on the right) at a camshaft end face.
4. Check up a condition of a sealing ring of round section, then establish the ignition distributor into place in the camshaft case.
5. Check up that rotor contact is located on one line with an arrow on the case of the distributor of ignition and establish a clip of the distributor of ignition.
6. Establish a cover of the distributor of ignition, screw in spark plugs and connect to them high-voltage wires.
7. Connect a vacuum tube to the ignition distributor.
8. Adjust a corner of an advancing of ignition.

MODELS 1,6 OF L WITH THE CARBURETTOR AND MODELS 1,4, 1,6 AND 1,8 L (18Е) WITH SYSTEM OF INJECTION OF FUEL

PERFORMANCE ORDER
1. Check up that the cranked shaft of the engine was not turned after removal of the distributor of ignition. Otherwise return a cranked shaft in a starting position.
2. Turn the ignition distributor so that contact of a rotor of the distributor was combined with an arrow or a label on the case of the distributor of ignition. In this position ledges on муфте a drive of the distributor of ignition will be established in position at which they will be established in a groove at a camshaft end face.
3. Check up a condition of a sealing ring of round section, then establish the ignition distributor into place in the camshaft case.
4. Check up that rotor contact is located on one line with an arrow on the case of the distributor of ignition and establish a clip of the distributor of ignition.
5. Establish a cover of the distributor of ignition, screw in spark plugs and connect to them high-voltage wires.
6. Connect a vacuum tube to the ignition distributor.
7. Adjust a corner of an advancing of ignition.

L MODELS 1,8 (18 SE)

PERFORMANCE ORDER
1. Grease working edges of a new sealing ring and establish it in a head of the block of cylinders. If necessary use tubular оправку the corresponding diameter.
2. Establish a rotor nave, thus combine apertures under bolts with apertures in a camshaft flange.
3. Establish a rotor and fix its screws.
4. Establish a new sealing ring of round section in a flute of the plastic screen. For simplification of installation of the plastic screen grease a sealing ring with pure engine oil.
5. Establish a cover of the distributor of ignition and fix screws.

MODELS 2,0 OF L WITH 8-Ю VALVES

PERFORMANCE ORDER
1. Grease working edges of a new sealing ring and establish it in a head of the block of cylinders. If necessary use tubular оправку the corresponding diameter.
2. Establish a rotor nave, thus combine apertures under bolts with apertures in a camshaft flange.
3. Establish a rotor and fix its screws.
4. Establish a new sealing ring of round section in a flute of the plastic screen.
5. For simplification of installation of the plastic screen grease a sealing ring with pure engine oil.

MODELS 2,0 OF L WITH 16 TH VALVES

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.
2. If necessary replace a sealing ring.
3. The rotor of the distributor of ignition can be established only in one position.