Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
- 10. Transmissions and power shafts
- 10.1. A mechanical transmission
10.1.1. A technical characteristics
10.1.2. Oil replacement in a transmission
10.1.3. Removal and installation of the lever of a gear change
10.1.4. Removal and installation of a cable of blocking of inclusion of a reverse gear
10.1.5. Removal, installation and adjustment of draught of a gear change
10.1.6. Replacement of sealing rings
10.1.7. Check, removal and installation of the switch of lanterns of a backing
10.1.8. Removal and installation of a drive of a speedometer
+ 10.1.9. A transmission
+ 10.2. An automatic transmission
+ 10.3. Power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes
|
Removal
| PERFORMANCE ORDER |
| 1. Loosen the tightening a bolt on муфте draughts of a gear change. |
| 2. Unscrew screws, fastening a protective tube of draught of a gear change to the car bottom. |
| 3. Shift back a rubber cover and disconnect the intermediate lever from the basis of the lever of a gear change. |
|
4. Remove a protective cover from the basis of the lever of a gear change. |
| 5. Remove draught from the car. |
| 6. Remove a rubber cover from a protective pipe. |
| 7. For draught dismantling beat out a cylindrical pin, крепящий the intermediate lever to a core, then beat out a core from the lever. |
| 8. Take a core from a protective pipe. |
| 9. For removal of the universal hinge сошлифуйте or drill heads of rivets. |
| 10. At installation it is necessary to use special pins and spring скобы which are necessary for getting before removal of rivets. |
| 11. Plugs can be taken from a protective pipe together with a core. |
|
Installation
| PERFORMANCE ORDER |
| 1. Fill with silicone greasing of a flute in pipe plugs. |
|
2. New цилиндрически a pin fix the intermediate lever to a core, thus their relative positioning should be such, as is shown in drawing. |
| 3. Establish a rubber cover and a casing, thus put on their internal surface silicone greasing. Do not move a protective casing after installation. |
| 4. Establish draught on the car, combining the intermediate lever with the gear change lever, and fix screws. |
| 5. Establish a rubber cover about the basis of the lever of a gear change. |
| 6. Adjust draught. |
|
Adjustment
| PERFORMANCE ORDER |
| 1. Remove the central console and establish the gear change lever in neutral position. |
|
2. Working in a motor compartment, a screw-driver remove a stopper from an adjusting aperture (it is specified by an arrow) and ослабьте tightening a bolt (is specified by an arrow) on муфте draughts of a gear change. |
| 3. Turn the rod of a gear change acting from a cover of the mechanism of a choice of transfers counter-clockwise if to look towards a forward part of the car, so, that in the selector lever it was possible to insert a shaft of a drill in diameter into adjusting apertures and corresponding apertures of 4,5 mm. |
|
4. Establish draught of a gear change (with the removed casing). |
|
5. Remove a rubber cover from the basis of the lever of a gear change and move the lever of transfers in neutral position on a line of inclusion of the first / second transfer. In this position adjusting labels (are specified by arrows) on the persistent plug and a casing of the lever of a gear change should be combined. |
| 6. While the assistant keeps the gear change lever, in this position tighten tightening a bolt муфты draughts of a gear change. |
| 7. Take a drill from an adjusting aperture. |
| 8. Check up that all transfers join well, then establish a new stopper on adjusting apertures. |
| 9. Establish a cover of the lever of a gear change and the central console. |
|
|
|
