Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
- 4. Cooling system
4.1. Specifications
4.2. Check of tightness of system of cooling
4.3. Check of density of a cooling liquid
4.4. A poliklinovoj belt
4.5. Tubes and hoses of system of cooling
4.6. The water pump of engine SOHC
4.7. The water pump of engine DOHC
4.8. A radiator
4.9. A radiator cover
4.10. Engine SOHC thermostat
4.11. Engine DOHC thermostat
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes
|
Removal
| PERFORMANCE ORDER |
| 1. Ослабьте bolts of fastening of a pulley of the water pump. | | 2. Ослабьте nuts of support of the generator. | | 3. Ослабьте a bolt of fastening of the generator also remove поликлиновой a belt. | | 4. Turn out bolts of fastening of a pulley of the water pump. The inhaling moment:
Sharnirnyj bolt () generator fastenings: 20–25 Н•м
Bolt () generator fastenings: 15–22 Н•м
Bolt of fastening of an arm of the generator: 20–28 Н•м | |
Check
Check up following elements and in the presence of defects replace them.
| PERFORMANCE ORDER |
| 1. Check up a surface поликлинового a belt on absence of damages and cracks. | | 2. Check up a surface поликлинового a belt on absence of oil and lubricant. |
| 3. Check up a surface поликлинового a belt on absence of non-uniform deterioration. | | 4. Check up a pulley surface on absence of cracks or damages. | |
Installation
| PERFORMANCE ORDER |
| 1. Establish a pulley of the pump and fix its bolts. |
| 2. After installation поликлинового a belt adjust its tension. | |
Installation
|
PERFORMANCE ORDER |
|
| 1. Check up a condition поликлинового a belt and its arrangement on pulleys. |
The prevention
Check up correctness of an arrangement of edges поликлинового a belt in flutes of pulleys.
If at work поликлиновой the belt publishes extraneous noise, check up a belt on absence of deterioration and damages, and also working surfaces of pulleys.
| |
| 2. By the special device measure a tension of a belt of a drive of the generator. In the absence of the special device, check up a belt tension, having pressed on it effort 100 Н (10 kg) in a place located on identical removal from pulleys and measure a belt deflection. Tension of a belt of a drive of the generator:
New belt: 65–75 kg
The belt which was in the use: 40 kg
Check: 35–50 kg
Tension of a belt of a drive of the generator and the pump of the amplifier of a steering:
New belt: 55–70 kg
The belt which was in the use: 38–48 kg
Tension of a belt of a drive of the generator and the conditioner:
New belt: 60–70 kg
The belt which was in the use: 32–40 kg
Check: 25–50 kg The belt which was in the use considers the belt which has worked on the engine more 5 minutes |
|
Tension measurement by the special device of type And
|
PERFORMANCE ORDER |
|
| At tension measurement поликлинового a belt, the device should not concern other elements of the engine. | |
Tension measurement by the special device of type In
|
PERFORMANCE ORDER |
| 1. At measurement, be convinced that have turned the button of repeated installation in an arrow direction to establish an arrow of the device in an initial condition. | | 2. After removal of the device from a belt, the marksman of the device will still specify a belt tension. | |
The prevention It is not recommended to regulate a belt tension by hand as this adjustment will not provide sufficient accuracy and the belt can slip on pulleys. Always use the special device.
Check up that the belt tension corresponds to demanded values.
Check a tension of a belt after a tightening шарнирного a bolt and a bolt of fastening of the generator.
|
|
