Hyundai Accent

10.5. A rotary fist and a nave of a forward wheel

1 – the bearing;
2 – a nut, 73–90 Н•м;
3 – a rack;
4 – a rotary fist;
5 – a tip of steering draught;
6 – a nut, 15–34 Н•м;
7 – a nave of a forward wheel; 8 – a brake disk;
9 – a nut, 220–260 Н•м;
10 – a brake board;
11 – a nut, 60–72 Н•м;
12 – a bolt, 65–75 Н•м;
13 – a lock spring ring.

Removal

PERFORMANCE ORDER

1. Lift the car and remove a forward wheel.

2. Turn out a nut of fastening of a power shaft.

3. Remove a support and a soft wire fix it on a forward rack.

4. Remove the gauge of frequency of rotation from a rotary fist.

5. Take шплинт and turn away a nut of fastening of a pin of the spherical hinge of a tip of steering bent for to a rotary fist. A stripper 09568–34000 squeeze out a pin of the spherical hinge from a rotary fist.

6. Note position and turn out bolts of fastening of the bottom part of a rack of a forward suspension bracket to a rotary fist.

7. A kapron hammer beat out a power shaft from a nave of a forward wheel. If the power shaft densely sits in a nave of a forward wheel, spray пропиточный aerosol solvent on area шлицов and then repeatedly screw a nut with a fillet so that it settled down flush with a shaft end face. Striking on a nut a brass hammer, beat out a power shaft from a nave.

8. A stripper 09568–34000 disconnect the spherical hinge of the bottom lever from a rotary fist.

9. Remove a rotary fist together with a nave of a forward wheel.

10. Installation is spent to sequences, return to removal.

Dismantling

PERFORMANCE ORDER

1. Remove a brake disk from a nave of a forward wheel.

2. Remove a lock spring ring.

3. Establish special tools, as is shown in drawing.

4. Turning the special tool, remove a nave of a forward wheel from a rotary fist.

5. Remove the special tool and a dustproof ring.

6. The special tool remove an internal ring of the bearing from a nave.

7. The special tool remove an external ring of the bearing from a rotary fist.

Check

PERFORMANCE ORDER

1. Check up a nave on absence of cracks and deterioration.

2. Check up a brake disk on absence of development and damages.

3. Check up the hinge on absence of cracks.

4. Check up a spring ring on absence of cracks or damages.

Assemblage

PERFORMANCE ORDER

1. Apply a thin film консистентной greasings in an aperture of a rotary fist and on an external ring of the bearing.

2. A press with оправкой the corresponding diameter запрессуйте the new bearing of a wheel.

The prevention
Do not make effort of a press an internal ring of the bearing.

3. Establish a dustproof ring.

4. A press with оправкой the corresponding diameter запрессуйте a nave in the wheel bearing.

The prevention
Do not make effort of a press an external ring of the bearing.

5. Establish a brake disk.

6. The special tool tighten a nave to a rotary fist, having tightened a bolt of the adaptation the moment 240 Н•м.

7. Some times turn a nave that bearing elements were established on the places.

8. Measure a twisting moment which is necessary for putting for проворачивания the bearing.
Twisting moment: 1,3 Н•м

9. If a twisting moment 0 Н•м, measure axial люфт the nave bearing.

10. If the twisting moment exceeds demanded value, means, the bearing is incorrectly established in a rotary fist and on a nave. Disassemble a rotary fist and repeatedly collect it.
Axial люфт the bearing: 0,08 mm

11. Remove the special tool.