Hyundai Accent

11.6. A rack of a back suspension bracket

1 – the bottom support of a spring;
2 – the top support of a spring;
3 – a rack arm;
4 – самоконтрящаяся a nut, 40–55 Н•м; 5 – a nut, 20–30 Н•м;
6 – a spring;
7 – a rack of a back suspension bracket;
8 – a nut, 75–90 Н•м.

Elements of a back suspension bracket

1 – a fixing element of a back axis;
2 – the bottom longitudinal lever;
3 – a bolt, 40–50 Н•м;
4 – a nut, 100–120 Н•м;
5 – the back stabilizer of cross-section stability;
6 – a bolt, 17–26 Н•м;
7 – a bolt, 35–45 Н•м; 8 – a nut , 130–150 Н•м;
9 – a nut , 100–120 Н•м;
10 – a nut , 88–100 Н•м;
11 – a nut , 130–150 Н•м;
12 – the bottom cross-section lever () a back suspension bracket;
13 – the bottom cross-section lever () a back suspension bracket.

The prevention
* Nuts which are necessary for tightening the demanded moment only after car installation on wheels are noted.

Removal

PERFORMANCE ORDER

1. Combine back sitting.

2. Remove a back cover from a wheel arch.

3. Turn out three top nuts of fastening of a back rack.

4. Remove a back wheel.

5. Disconnect from a back rack a brake tube and the gauge of frequency of rotation of a wheel.

6. Turn away a nut and get bolts of fastening of a rack to a fixing element of a back axis and get a rack from under a car wing.

The prevention
Be careful not to damage a rack of a back suspension bracket.

Dismantling

PERFORMANCE ORDER

1. The special adaptation compress a spring of a rack of a back suspension bracket.

The prevention
For spring compression use only the reliable tool.

2. Turn away a lock nut in the top part of a rod of the shock-absorber.

3. Remove a rack support, the top support of a spring, a cylindrical spring, a dustproof cover and the bottom support of a spring.

Check

PERFORMANCE ORDER

1. Check up a rack support on absence of deterioration or damages.

2. Check up rubber details on absence of damages or deterioration of their condition.

3. Check up a cylindrical spring on absence of a deflection and elasticity loss.

4. Check up the shock-absorber as follows:

a. Undertake a hand a rod of the shock-absorber and some times press and extend it from the shock-absorber;
b. Check up that the rod moves smoothly, without jammings, and the effort put to a rod, does not change with each course;
c. Be convinced that at rod moving there are no extraneous noise.

Assemblage

PERFORMANCE ORDER

1. Establish the bottom support of a spring so that its ledges have entered into apertures of a plate of a spring.

2. Establish on the shock-absorber a dustproof cover.

3. The special adaptation compress a spring of a rack of a forward suspension bracket. After full compression of a spring establish it on the shock-absorber.

4. Completely extend a rod of the shock-absorber and establish the top support of a spring and a rack support.

The prevention
Combine a D-shaped aperture in the top support of a spring with лыской on a shock-absorber rod.

5. Correctly arrange the top and bottom ends of a cylindrical spring, having established them in dredging, and screw самоконтрящуюся a nut, but do not tighten it definitively.

6. Arrange a bolt of fastening of a support of a spring so that to combine projections of linings, as is shown in drawing.

7. Remove the adaptation for spring compression.

8. Tighten самоконтрящуюся a nut the demanded moment of an inhaling.
The inhaling moment: 40–55 Н•м