Hyundai Accent

Repair and car operation


Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
- 14. A body
   14.1. Specifications
   14.2. Adjustment of hinges of a cowl
   14.3. A luggage carrier cover
   14.4. Adjustment of a door of a luggage space
   14.5. A forward door
   14.6. A back door
   14.7. Молдинги
   14.8. The roof hatch
   14.9. An external rear-view mirror
   14.10. The central console
   14.11. The panel of devices
   14.12. Ceiling furnish
   14.13. A back shelf
   14.14. A luggage carrier upholstery
   14.15. An internal upholstery of salon
   14.16. A windscreen
   14.17. Back glass
   14.18. A forward bumper
   14.19. A back bumper
   14.20. A back seat
   14.21. A forward seat
   14.22. Search and elimination of malfunctions
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

944881c0





14.16. A windscreen
1 – распорная the windscreen plug;
2 – молдинг a windscreen;
3 – an internal rear-view mirror; 		4 – a windscreen;
5 – a windscreen lining.

Removal

PERFORMANCE ORDER
1. Before windscreen removal remove following elements:

- The top upholstery of a forward rack;
- Internal rear-view mirror;
- Screen wiper levers;
- Overlay of the top part of a cowl;
- молдинг a windscreen.
2. The special tool 09861-31100 cut hermetic of fastening of a windscreen.
3. If glass is repeatedly established, leave a hermetic layer on glass and a body. Note glass position on a car body.
4. The special tool 09861-31400 remove a windscreen from the car.

Installation

PERFORMANCE ORDER
1. The special tool or a knife cut off old hermetic till a thickness of a layer of 2 mm on all perimetre of a framework and a windscreen.
The prevention

Be cautious not to remove some hermetic more than it is necessary, and also not to damage a paint and varnish covering of the car.

2. Degrease the processed surface.
3. Put a windscreen to a window aperture and in four points on a body note glass installation sites.
4. Paste a rubber lining to an internal surface of a windscreen.

Height of a layer of hermetic:
Above: 13,5 mm
From sides: 13,5 mm
From below: 27 mm
5. Establish a windscreen.
6. Apply a thin film a glass first coat on an outer side of a rubber lining of a windscreen.
The prevention

Do not concern a layer of hermetic with a hand.
In a place of a contact of hermetic it cannot provide with a hand reliable connection and in this place leaks after glass installation are possible.
Do not put on glass a first coat intended for a body.
7. Apply a thin film first coats on originally put hermetic acting on perimetre of glass. Glass is necessary for establishing during 10 mines after first coat drawing.
8. Put glue in a syringe and put it on windscreen edge.
The prevention

Put glue during 5 mines after drawing of a glass first coat.
9. The special tool or suckers establish glass over a window aperture according to earlier put labels and press glass to a window aperture.
10. Шпателем remove superfluous glue. Fill all bowls and emptiness on windscreen perimetre.
11. Directing a water stream on a windscreen, check up tightness of its installation. Do not direct on fresh hermetic a water stream under the big pressure.
12. In the presence of leaks dry up the damaged area and put hermetic.
The prevention

Do not maintain the car within 4 hours after glass installation.
After windscreen installation support it within the first hour.
13. Establish into place all earlier removed elements.
The prevention

Within 2-3 days after installation of a windscreen do not clap doors.
Avoid movement on rough roads where the car body is exposed to intensive twisting.