Hyundai Accent

Repair and car operation

Hyundai Accent
+ 1. The maintenance instruction
- 2. The engine
   + 2.1. Engines SOHC
   - 2.2. Engines DOHC
      2.2.1. Specifications
      2.2.2. Compression check
      2.2.3. A gear belt
      2.2.4. A poliklinovoj belt
      2.2.5. Engine support
      2.2.6. A forward cover
      2.2.7. The air filter (ACL)
      2.2.8. A head of cylinders
      2.2.9. Camshafts
      2.2.10. Replacement of a saddle of the valve
      2.2.11. Replacement of the directing plug of the valve
      2.2.12. The valve
      2.2.13. Rods
      2.2.14. A cranked shaft
      2.2.15. A flywheel
      2.2.16. The piston
      2.2.17. A final collector
      2.2.18. An inlet collector and the air chamber
      2.2.19. The block of cylinders
      2.2.20. Removal and engine and transmission installation
      2.2.21. System of release of the fulfilled gases
      2.2.22. Search and elimination of malfunctions
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

2.2.3. A gear belt

1 – a forward cover;
2 – a bolt, 20–27 Н•м;
3 – распорная the plug of the mechanism of a tension of a gear belt;
4 – a spring of the mechanism of a tension;
5 – a roller of a tension of a gear belt;
6 – a camshaft pulley;
7 – an adjusting label (index);
8 – an aperture of an adjusting label;
9 – the free party of a gear belt; 10 – an adjusting pin;
11 – a bolt, 80–100 Н•м;
12 – a directing roller;
13 – a bolt, 43–55 Н•м;
14 – the party of a tension of a gear belt;
15 – an adjusting label (index) on a forward cover;
16 – an adjusting label on a pulley of a cranked shaft;
17 – a pulley of a cranked shaft.

Removal

PERFORMANCE ORDER

1. Ослабьте a bolt of fastening of a pulley of the water pump.

2. Ослабьте a bolt of fastening of the generator.

3. Remove a pulley of the water pump and a belt.

4. Remove a pulley of a cranked shaft.

5. Remove a casing of a gear belt.

6. Move a roller of a tension of a gear belt to the water pump and temporarily fix it in this position.

7. Turn out a bolt of fastening of a pulley of a camshaft.

8. Remove a camshaft pulley.

9. Remove a gear belt.

The prevention
Note a direction of rotation of a gear belt for its repeated installation in initial position.

10. Turn out a bolt of fastening of a pulley of a cranked shaft. Remove a pulley of a cranked shaft and the plug.
11. Remove a roller of the mechanism of a tension of a gear belt.

Check

Pulleys and roller of the mechanism of a tension of a gear belt

PERFORMANCE ORDER

1. Check up pulleys of distributive and cranked shaft, a roller of the mechanism of a tension and a single pulley on absence of non-uniform deterioration, cracks and damages.

2. Check up ease and smoothness of rotation of a roller of the mechanism of a tension and a single pulley, and also absence of extraneous noise at rotation.

Gear belt
The prevention
Strongly do not bend a gear belt and do not change a direction of its rotation. Do not allow oil and lubricant to contact with a gear belt as it will lead to its destruction.

PERFORMANCE ORDER

1. Check up a gear belt on absence of damages, deterioration, stratification, cracks on teeths and in the basis of teeths, and also on defects at end faces and a belt underside.

2. In the presence of following defects, replace a gear belt.

The description

Defect

1. A rigid return surface of a gear belt. The surface has a glossy appearance
Rigidity of a surface is that that the nail does not leave traces on a belt

2. Cracks on a return surface of a gear belt

3. Cracks or stratification of a gear belt

4. Strongly worn out teeths
The tooth party is worn out, fibres, a cord and the rubber basis become thus visible

5. Teeths (last stage) are worn strongly out
The tooth party is worn out, attritions become thus visible and the thickness of a tooth is reduced

6. Cracks in the basis of teeths

7. Absence of a tooth

8. Strong deterioration of one party of a belt

9. Cracks on a lateral face of a gear belt

Installation

PERFORMANCE ORDER

1. Establish the plug, and a pulley of a cranked shaft as is shown in drawing. Pay attention to a direction of their installation
The inhaling moment: 140–150 Н•м

2. Establish a pulley of a camshaft and fix a bolt, having tightened its demanded moment.

The inhaling moment: 80–100 Н•м

3. Establish directing roller and fix a bolt, having tightened its demanded moment.

The inhaling moment: 43–55 Н•м

4. Combine adjusting labels on pulleys of distributive and cranked shaft with indexes, thus the piston of the first cylinder should be established in ВМТ in a compression step.

5. At installation of the mechanism of a tension of a gear belt first of all establish the tension mechanism, a spring and распорную the plug. Temporarily tighten bolts. Then, temporarily compress the tension mechanism, having inserted a bolt into the extended aperture. Establish the back end of a flat spring opposite to a forward cover, as is shown in drawing.

6. Fix the mechanism of the tension which have been taken away to the water pump.

7. Establish a gear belt on a pulley of a cranked shaft.

8. Establish a gear belt on a camshaft pulley, be thus convinced that its sagging from outside tension is excluded.

9. Ослабьте bolts of 1 and 2 fastenings of the mechanism of a tension in the sequence shown in drawing, the spring of the mechanism of a tension of a gear belt thus will be unclenched.

10. Tighten bolts of 1 and 2 fastenings of the mechanism of a tension in the same order.
11. Turn clockwise a cranked shaft of the engine on two complete revolutions and combine a label on a pulley of a gear belt of a cranked shaft with the index on the block of cylinders of the engine. Check up that the label on a camshaft pulley was combined with the index on a cover of a head of cylinders.

The prevention
Do not turn a cranked shaft of the engine counter-clockwise.

12. In the same order ослабьте bolts of 1 and 2 fastenings of the mechanism of a tension of a gear belt.
13. Tighten bolts of 1 and 2 fastenings of the mechanism of a tension in the same order.
The inhaling moment: 20–27 Н•м

14. Repeatedly check up a tension of a gear belt. By pressing the tense branch of a gear belt effort 49 Н the gear belt should cave in to the centre of a head of a bolt of fastening of the mechanism of a tension.
15. Establish casings of a gear belt.

The inhaling moment: 8–10 Н•м
16. Establish a pulley of a cranked shaft.
The inhaling moment: 140–150 Н•м

17. Establish поликлиновой a belt of a drive of the fan and adjust its tension.
18. Establish a pulley of the water pump.
19. Establish поликлиновой a belt and adjust its tension.