Hyundai Accent

Repair and car operation

Hyundai Accent
+ 1. The maintenance instruction
- 2. The engine
   + 2.1. Engines SOHC
   - 2.2. Engines DOHC
      2.2.1. Specifications
      2.2.2. Compression check
      2.2.3. A gear belt
      2.2.4. A poliklinovoj belt
      2.2.5. Engine support
      2.2.6. A forward cover
      2.2.7. The air filter (ACL)
      2.2.8. A head of cylinders
      2.2.9. Camshafts
      2.2.10. Replacement of a saddle of the valve
      2.2.11. Replacement of the directing plug of the valve
      2.2.12. The valve
      2.2.13. Rods
      2.2.14. A cranked shaft
      2.2.15. A flywheel
      2.2.16. The piston
      2.2.17. A final collector
      2.2.18. An inlet collector and the air chamber
      2.2.19. The block of cylinders
      2.2.20. Removal and engine and transmission installation
      2.2.21. System of release of the fulfilled gases
      2.2.22. Search and elimination of malfunctions
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

2.2.4. A poliklinovoj belt Removal

PERFORMANCE ORDER

1. Ослабьте bolts of fastening of a pulley of the water pump.

2. Ослабьте nuts of support of the generator.

3. Ослабьте a bolt of fastening of the generator also remove поликлиновой a belt.

4. Turn out bolts of fastening of a pulley of the water pump.

The inhaling moment:
Sharnirnyj bolt () generator fastenings: 20–25 Н•м the Bolt () generator fastenings: 15–22 Н•м the Bolt of fastening of an arm of the generator: 20–28 Н•м

Check

Check up following elements and in the presence of defects replace them.

PERFORMANCE ORDER

1. Check up a surface поликлинового a belt on absence of damages and cracks.

2. Check up a surface поликлинового a belt on absence of oil and lubricant.

3. Check up a surface поликлинового a belt on absence of non-uniform deterioration.

4. Check up a pulley surface on absence of cracks or damages.

Installation

PERFORMANCE ORDER

1. Establish a pulley of the pump and fix its bolts.

2. Establish a pulley of the pump and fix its bolts.

Check and tension adjustment

PERFORMANCE ORDER

1. Check up a condition поликлинового a belt and its arrangement on pulleys.

The prevention
Check up correctness of an arrangement of edges поликлинового a belt in flutes of pulleys.
If at work поликлиновой the belt publishes extraneous noise, check up a belt on absence of deterioration and damages, and also working surfaces of pulleys.

2. By the special device measure a tension of a belt of a drive of the generator. In the absence of the special device check up a belt tension, having pressed on it effort 100 Н (10 kg) in a place located on identical removal from pulleys and measure a belt deflection.
Deflection of a belt of a drive of the generator at tension check:
New belt: 7,5–9,0 mm//64–73 kg
The belt which was in the use: 9,0–10,4 mm//39 kg
Check: 5,0–6,0 mm / of 34-49 kg
Deflection of a belt of a drive of the generator and the pump of the amplifier of a steering at tension check:
New belt: 8 mm
The belt which was in the use: 6,0–7,0 mm
Deflection of a belt of a drive of the generator and the conditioner at tension check:
New belt: 6,0–9,0 mm
The belt which was in the use: 9,0–10,0 mm

The prevention
The belt which was in the use considers the belt which has worked on the engine more 5 minutes

Tension measurement by the special device

PERFORMANCE ORDER

1. At tension measurement поликлинового a belt the device should not concern other elements of the engine.

2. Adjust a deflection or a tension of a belt of the pump of the amplifier of a steering.

3. Tighten an adjusting bolt.

4. Turn a cranked shaft of the engine on some turns.

5. Check up a tension of a belt and, if necessary, repeat adjustment.