Opel Kadett E

1984-1991 of release

Repair and car operation


Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
- 6. Fuel and exhaust systems
   - 6.1. Models with the carburettor
      6.1.1. A technical characteristics
      6.1.2. Use unleaded gasoline
      6.1.3. Removal and installation of the case of the air filter
      6.1.4. System of adjustment of temperature of air arriving in the engine
      6.1.5. Check, removal and installation of the fuel pump
      6.1.6. Removal and installation of the gauge of level of fuel
      6.1.7. Removal and installation of a fuel tank
      6.1.8. Removal, installation and adjustment of a cable of an accelerator
      6.1.9. Removal and installation of a pedal of an accelerator
      6.1.10. Removal, installation and adjustment of a cable of management air заслонкой
      + 6.1.11. Carburettors
      6.1.12. Check of the electromagnetic valve of a stopping delivery of fuel
      6.1.13. Removal and carburettor installation
      - 6.1.14. Carburettor repair
         6.1.14.1. The carburettor 32 ТL
         6.1.14.2. The carburettor 35 PDSI
         6.1.14.3. The carburettor 1В1
         6.1.14.4. The carburettor 2Е3
         + 6.1.14.5. Carburettor Varajet II
      6.1.15. Removal and installation of an inlet collector
      6.1.16. Removal and installation of a final collector
      6.1.17. Removal and installation of a heater of an inlet collector
      6.1.18. Removal and exhaust system installation
   + 6.2. Models with system of injection of fuel
   + 6.3. Models with engines 16D and 16DA
   + 6.4. Models with engines 17D and 17DR
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes


944881c0

6.1.14.3. The carburettor 1В1
PERFORMANCE ORDER
1. Remove the carburettor from the engine.
2. Remove a hose of the vacuum chamber of moving from the throttle case.
3. Unscrew four screws and remove the top cover of the carburettor.
4. Unscrew screws (adjustments of turns of idling and quality of a mix are specified by arrows), and also the valve blocking giving of fuel on turns of idling or заглушку (it is specified by an arrow).
5. Unscrew a nut, note an arrangement and remove the lever of a drive throttle заслонки, a plate of a cam and a returnable spring.
6. Unscrew two screws and uncover devices of enrichment of partial loading, a spring and a diaphragm.
7. Remove a flange of the accelerating pump.
8. Remove the piston of the accelerating pump.
9. Remove a spring of the accelerating pump.
10. Take a spray of the accelerating pump from the carburettor. Remove a spring and a ball.
11. Выпрессуйте a float axis, then remove a float.
12. Remove the needle valve.
13. Unscrew and remove the main jet.
14. Unscrew three screws and remove заслонку, thermal and vacuum chambers.
15. Note an arrangement and unscrew and remove a fuel / air jet of turns of idling () and additional () a fuel / air jet from the carburettor case.
16. The further dismantling of the carburettor is not recommended.
17. Clear carburettor details in gasoline and blow their compressed air.
18. Blow compressed air all jets and channels in the carburettor, but thus do not use a wire.
19. Check up a condition of all axes and draughts on presence of deterioration and the increased backlash. In the presence of defects replace the worn out details.
20. Check up a condition of diaphragms and replace them in the presence of punctures and pollution.
21. Check up a condition and tightness of a float. If in a float there is a fuel, replace it.
22. Blowing the needle valve, check up its tightness in the closed position. In the absence of tightness replace the needle valve.
23. Carburettor assemblage is made in sequence, return to removal. The top position of a float is not regulated.
24. Establish the carburettor on the engine and adjust turns of idling and quality of a mix, then execute other adjustments.