Opel Kadett E

1984-1991 of release

Repair and car operation


Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. A suspension bracket and a steering
   12.1. A technical characteristics
   + 12.2. A rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. The bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. A nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. The back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a self-levelled back suspension bracket
   12.15. Removal and steering wheel installation
   + 12.16. A steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draught
   + 12.19. Steering transfer
   12.20. Removal of air from system of a steering with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation пополнительного a tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. A body
+ 14. Electric schemes


944881c0

12.10. Replacement of back springs
THE GENERAL DATA
The prevention

Replacements of springs of a back suspension bracket make in pairs.

PERFORMANCE ORDER
1. On cars with a self-levelled back suspension bracket remove pressure in system.
2. Lift a back part of the car and fix on supports.
Hatchback and Sedan
3. Using the special tool, unload the shock-absorber on the one hand the car for what raise a jack the longitudinal lever (diameter And corresponds to the sizes of a jack).
4. Unscrew bolts of the bottom fastening of the shock-absorber and take the bottom part of the shock-absorber from an arm.
5. Lower a jack and remove a spring and rubber буферы. If necessary for spring extraction reject the longitudinal lever of a back suspension bracket downwards.
6. At installation of a new spring it is necessary to establish new rubber буферы.
7. Establish a spring and rubber буферы, then lift the longitudinal lever of a back suspension bracket and fix the bottom part of the shock-absorber.
8. At installation of conic springs check up correctness of an arrangement (it is specified by arrows) extreme top coils of a spring in a spring support.
9. Similarly replace a spring from the second party of the car.
10. On models with a self-levelled back suspension bracket increase pressure in system to 0,8 bar.
The versatile person and the Van
11. A jack raise one of longitudinal levers of a back suspension bracket and unscrew a bolt of the bottom fastening of the shock-absorber.
12. Lower a jack and repeat this operation on the other hand the car, leaving a jack on a place.
13. Remove springs, if necessary lowering a jack.
14. At replacement of the top buffers of a spring paste them into place.
15. Establish a spring. At installation of conic springs check up correctness of an arrangement (it is specified by arrows) top coils of a spring.
16. Lift a jack and fix the bottom part of the shock-absorber.
17. Rearrange a jack on other party of the car and fix the bottom part of the second back shock-absorber.
18. Tighten bolts of the bottom fastening of shock-absorbers the demanded moment.
19. On models with a self-levelled back suspension bracket increase in system pressure to 0,8 bar.