Opel Kadett E

1984-1991 of release

Repair and car operation


Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. A suspension bracket and a steering
   12.1. A technical characteristics
   + 12.2. A rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. The bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. A nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. The back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a self-levelled back suspension bracket
   12.15. Removal and steering wheel installation
   + 12.16. A steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draught
   + 12.19. Steering transfer
   12.20. Removal of air from system of a steering with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation пополнительного a tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. A body
+ 14. Electric schemes


944881c0

12.6. Adjustment of the bearing of a back wheel MODELS TILL 1992

PERFORMANCE ORDER
The prevention

For fastening of a nut of a nave it is necessary to use new шплинт.
1. At presence remove a wheel cap, then ослабьте bolts of fastening of a back wheel.
2. Lift a back part of the car and fix on supports.
3. Remove a back wheel.
4. Using a screw-driver edge, remove a dustproof cap from a nave.
5. Take шплинт, fixing a nut of a nave from unscrewing, then ослабьте a nut of fastening of a nave.
6. Tighten a nut of fastening of a nave the moment of 25 Nanometers, thus turn a nave.
7. Loosen the a nut of fastening of a nave until while the persistent washer located under a nut, it will be possible to move a screw-driver edge every which way.
8. Establish new шплинт, fixing a nut of a nave from unscrewing. Thus, if the aperture under шплинт in a pin is not combined with grooves on a nave nut, tighten a nut before combination of an aperture with the nearest groove.
9. Check up that the persistent washer can still move. Otherwise ослабьте a nut before combination of the nearest groove on a nut with an aperture in a nave pin.
10. Establish a wheel and lower the car.
11. Tighten bolts of fastening of a wheel the demanded moment.

MODELS SINCE 1992

Not folding knot of a nave and the bearing of a back wheel on models since 1992

 1 – a nave,

2 – a fixing element of a nave,

3 – a bolt,

4 – a dustproof cap,

5 – the bearing,

6 – a sealing ring,

7 – gauge ABS

Since 1992 on all models not folding knot of a nave and the bearing of a back wheel is established.

As the knot consisting of a fixing element of a nave, a nave and the nave bearing, is not folding knot, bearing adjustment is not required.