Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
- 16. The electric equipment
   16.1. Specifications
   16.2. Electric chains
   16.3. Gymnastics system
   16.4. Check of an electric chain of gymnastics
   16.5. Power failure check on a wire connecting the storage battery with the generator
   16.6. Check of the current developed by the generator
   16.7. Check of developed pressure
   16.8. The generator
   16.9. The storage battery
   16.10. Check of relative density of electrolit
   16.11. Gymnastics of the storage battery
   16.12. Survey of the storage battery
   16.13. Start system
   16.14. A starter
   16.15. Check and replacement of elements статора
   16.16. The switch of blocking of ignition
   16.17. Check of the relay of a starter
   16.18. Check of the switch of blocking of ignition
   16.19. A radio receiver
   16.20. Dynamics
   16.21. The aerial
   16.22. The multipurpose switch
   16.23. A sound signal
   16.24. Safety locks
   16.25. A combination of devices
   16.26. The engine of a screen wiper of a windscreen
   16.27. Replacement of a headlight and the forward index of turn
   16.28. Adjustment of light of headlights
+ 17. The appendix
+ 18. Electroschemes


944881c0






16.15. Check and replacement of elements статора Adjustment of a backlash of a gear wheel

PERFORMANCE ORDER
1. Disconnect a wire from the M. plug
2. Additional wires connect plugs of the storage battery to plugs S and M.
3. Include ignition, thus a starter gear wheel it will be pushed forward.


The prevention

This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.


4. Щупом check up a backlash between a gear wheel and a stopper. If the backlash differs from demanded, adjust it, adding or cleaning linings between the traction relay and a forward cover.

Gear wheel backlash: 0,5–0,2 mm

Check of the traction relay of a starter

PERFORMANCE ORDER
1. Disconnect a wire from the M. plug
2. Additional wires connect plugs of the storage battery to plugs S and M.
3. Include ignition, thus a starter gear wheel it will be pushed forward. If the gear wheel is not put forward, replace the traction relay.

The prevention

This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.



Check of a keeping winding of the traction relay

PERFORMANCE ORDER
1. Disconnect a wire from the M. plug
2. Additional wires connect plugs of the storage battery to plug S and the case of the traction relay.

The prevention

This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.


3. If the gear wheel remains on a place, means, the keeping winding of the traction relay is damaged and, it is necessary to replace the traction relay.

Return check плунжера the traction relay

PERFORMANCE ORDER
1. Disconnect a wire from the M. plug
2. Additional wires connect plugs of the storage battery to the plug of M and the case of the traction relay.

The prevention

This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.


3. The starter gear wheel should be pushed forward. After a detachment of wires the starter gear wheel quickly should return to a starting position.

Operational tests (idling)


PERFORMANCE ORDER
1. For carrying out of tests of idling collect the scheme shown in drawing.
2. Establish a rheostat cursor in such position at which the voltmeter will show pressure 11,5 In, thus check up a current consumed by a starter, and be convinced that the starter shaft is turned easily and smoothly.

Current: no more than 60 And

Gear wheel with обгонной муфтой


PERFORMANCE ORDER
1. To remove обгонную муфту from a rotor shaft, it is necessary to remove a persistent ring preliminary.
2. Move a persistent ring to a gear wheel and remove a spring ring. Now the persistent ring can be removed from a shaft.

Check of a winding of a rotor


PERFORMANCE ORDER
1. An ohmmeter check up conductivity between a collector and a rotor. In the presence of conductivity replace a rotor.
2. In the special device check up a rotor winding.

In the presence of short circuits replace a rotor. If the steel strip enclosed to a rotor, vibrates, means, in rotor windings there are short circuits.
3. An ohmmeter check up conductivity between collector segments. In the absence of conductivity replace a rotor.

Check of coils статора


PERFORMANCE ORDER
1. An ohmmeter check up conductivity of coils статора. In the absence of conductivity replace coils статора.
2. With the coil established in the case, check up conductivity between a conclusion of the coil and the starter case. In the presence of conductivity replace coils статора.

Check of brushes

PERFORMANCE ORDER
If the brush is worn out to the designated limit, replace it.

Check щеткодержателя

PERFORMANCE ORDER
Ohmmeter check up conductivity between each isolated brush and a plate. In the presence of conductivity replace щеткодержатель.

Check обгонной муфты

PERFORMANCE ORDER
Check up a condition of teeths of a gear wheel обгонной муфты and, in the presence of damages, replace it. Also check up a condition of teeths of a gear wreath of a flywheel.

Turn a gear wheel. The gear wheel should be turned freely clockwise and be blocked at проворачивании counter-clockwise

Replacement of brushes

PERFORMANCE ORDER
1. Remove the worn out brush, thus be careful not to damage a wattled wire.
2. An emery paper smooth out the end of a wattled occasion to provide its reliable contact to a new brush.
3. Solder a wattled wire.

Replacement of the back plug


PERFORMANCE ORDER
1. Before to remove the plug, it is necessary to measure depth of its installation.
2. The plug can be removed by means of a stripper, as is shown in drawing.
3. Establish the new plug on preliminary measured depth.

Starter assemblage

PERFORMANCE ORDER
1. Establish обгонную муфту on the forward end of a shaft of a rotor.
2. Establish a persistent ring and a spring ring from the forward party of a shaft of a rotor then move a persistent ring completely to a spring ring.
3. At lever installation in a forward cover pay attention to its position. If the lever to establish on the contrary, the gear wheel will be put constantly forward outside and cannot work properly.