Hyundai Accent

Repair and car operation


Hyundai Accent
+ 1. The maintenance instruction
- 2. The engine
   - 2.1. Engines SOHC
      2.1.1. Specifications
      2.1.2. A gear belt
      2.1.3. Check of a tension of a gear belt
      2.1.4. Adjustment of a tension of a gear belt
      2.1.5. A poliklinovoj belt
      2.1.6. Engine support
      2.1.7. A forward cover and the oil pump
      2.1.8. The air filter (ACL)
      2.1.9. A head of cylinders
      2.1.10. Коромысла
      2.1.11. Hydraulic jacks of backlashes of valves
      2.1.12. Replacement of a saddle of the valve
      2.1.13. Replacement of the directing plug of the valve
      2.1.14. The valve
      2.1.15. A camshaft
      2.1.16. Rods
      2.1.17. A cranked shaft
      2.1.18. A flywheel
      2.1.19. A piston finger
      2.1.20. A final collector
      2.1.21. An inlet collector and the air chamber
      2.1.22. The block of cylinders
      2.1.23. Removal and engine and transmission installation
      2.1.24. System of release of the fulfilled gases
      2.1.25. Search and elimination of malfunctions
   + 2.2. Engines DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

944881c0





2.1.15. A camshaft
1 – a bolt, 80–100 Н•м;
2 – a washer; 		3 – an adjusting pin;
4 – a camshaft.

Removal
PERFORMANCE ORDER
1. Disconnect a ventilation hose картера.
2. Remove a pulley of the water pump and a cranked shaft.
3. Remove a casing of a gear belt.
4. Take away a roller of a tension of a gear belt to the water pump and temporarily fix it in this position.
5. Remove a gear belt from a camshaft pulley.
6. Remove a camshaft pulley.
7. Remove a camshaft pulley.
8. Uncover heads of cylinders.
9. Remove in gathering a shaft коромысел.
10. Remove covers of bearings of a camshaft.
11. Remove a camshaft.

Check
PERFORMANCE ORDER
1. Check up a camshaft on absence of non-uniform deterioration, cracks or damages.
2. In two points measure height of each cam of a camshaft.

Nominal height of cams of a camshaft of inlet valves: 42,8575 mm
Nominal height of a camshaft of final valves: 42,7354 mm
Is minimum admissible height of cams of a camshaft of inlet valves: 42,3575 mm
Is minimum admissible height of a camshaft of final valves: 42,2353 mm

3. Check up surfaces of cams on absence of non-uniform deterioration and damages.
4. Check up each bearing on absence of damages. If the working surface of the bearing is excessively damaged, replace a head of cylinders or a cover of the bearing of a camshaft.

Forward sealing ring of a camshaft

PERFORMANCE ORDER
1. Check up working edges of a sealing ring on absence of deterioration. If the working edge is worn out or damaged, replace a sealing ring.
2. Check up the surface of a camshaft contacting to a sealing ring. If this surface is worn in regular intervals out, replace a camshaft.

Axial люфт a camshaft: 0,07–0,28 mm.

Installation

PERFORMANCE ORDER
1. Before installation apply a thin film pure engine oil on all surfaces of sliding of a camshaft. Establish a camshaft.
2. Establish covers of bearings of a camshaft.
3. Establish the ignition coil.
4. Establish a shaft коромысел and коромысла.
5. Grease with engine oil working edges and an external surface of a sealing ring and the special tool 09221-21000 establish a sealing ring on a forward part of a camshaft.
Hammer blows on the special adaptation establish a sealing ring against the stop in a nest.
6. Establish a pulley of a camshaft and fix its bolt.

The inhaling moment: 80–100 Н•м

7. Combine an adjusting label of a camshaft and an adjusting label of a pulley of a cranked shaft with indexes, thus the piston of 1st cylinder will be in ВМТ in a compression step.
8. Establish a lining in deepening of a cover of a head of cylinders.
9. Temporarily establish a cover of a head of cylinders.
10. Start up the engine and leave it to work on frequency of rotation of a cranked shaft idling.
11. Tighten bolts of fastening of a cover the demanded moment.

The inhaling moment: 8–10 Н•м

12. Establish casings of a gear belt.
13. Establish a pulley of the water pump and a pulley of a cranked shaft.