Hyundai Accent

Repair and car operation


Hyundai Accent
+ 1. The maintenance instruction
- 2. The engine
   - 2.1. Engines SOHC
      2.1.1. Specifications
      2.1.2. A gear belt
      2.1.3. Check of a tension of a gear belt
      2.1.4. Adjustment of a tension of a gear belt
      2.1.5. A poliklinovoj belt
      2.1.6. Engine support
      2.1.7. A forward cover and the oil pump
      2.1.8. The air filter (ACL)
      2.1.9. A head of cylinders
      2.1.10. Коромысла
      2.1.11. Hydraulic jacks of backlashes of valves
      2.1.12. Replacement of a saddle of the valve
      2.1.13. Replacement of the directing plug of the valve
      2.1.14. The valve
      2.1.15. A camshaft
      2.1.16. Rods
      2.1.17. A cranked shaft
      2.1.18. A flywheel
      2.1.19. A piston finger
      2.1.20. A final collector
      2.1.21. An inlet collector and the air chamber
      2.1.22. The block of cylinders
      2.1.23. Removal and engine and transmission installation
      2.1.24. System of release of the fulfilled gases
      2.1.25. Search and elimination of malfunctions
   + 2.2. Engines DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

944881c0





2.1.4. Adjustment of a tension of a gear belt Adjustment of a tension of a gear belt is made automatically by the tension mechanism.

PERFORMANCE ORDER
1. Turn a steering wheel against the stop counter-clockwise.
2. Prop up the oil pallet of the engine wooden бруском and raise the engine a little.
3. Remove the left support of the engine.
4. Remove a pulley of the water pump.
5. Remove a pulley of a cranked shaft.
6. Remove the top casing of a gear belt.
7. Check up a gear belt on absence of stratifications, damages and other defects. Be convinced that have carefully checked up a belt on all length.
8. Turn a cranked shaft of the engine so that the piston of the first cylinder was established in ВМТ in a compression step. Combine a label on a pulley of a gear belt of a cranked shaft with the index on the block of cylinders of the engine. Check up that a label on a camshaft pulley were combined with the index on a cover of a head of cylinders.
9. Remove the bottom casing of a gear belt.
10. Ослабьте bolts of 1 and 2 fastenings of the mechanism of a tension in the sequence shown in drawing, the spring of the mechanism of a tension of a gear belt thus will be unclenched.
11. Check up a belt arrangement on engine pulleys.
12. Tighten bolts of 1 and 2 fastenings of the mechanism of a tension in the same order.
13. Turn clockwise a cranked shaft of the engine on one complete revolution and combine a label on a pulley of a gear belt of a cranked shaft with the index on the block of cylinders of the engine.
The prevention

Do not turn a cranked shaft of the engine counter-clockwise.
14. In the same order ослабьте bolts of 1 and 2 fastenings of the mechanism of a tension of a gear belt.

15. Repeatedly tighten bolts of 1 and 2 fastenings of the mechanism of a tension in the same order.

The inhaling moment: 20-27 Н•м
16. Repeatedly check up a tension of a gear belt. By pressing the tense branch of a gear belt with effort 49 Н the gear belt should cave in to the centre of a head of a bolt of fastening of the mechanism of a tension.