Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
- 2. The engine
   - 2.1. Engines SOHC
      2.1.1. Specifications
      2.1.2. A gear belt
      2.1.3. Check of a tension of a gear belt
      2.1.4. Adjustment of a tension of a gear belt
      2.1.5. A poliklinovoj belt
      2.1.6. Engine support
      2.1.7. A forward cover and the oil pump
      2.1.8. The air filter (ACL)
      2.1.9. A head of cylinders
      2.1.10. Коромысла
      2.1.11. Hydraulic jacks of backlashes of valves
      2.1.12. Replacement of a saddle of the valve
      2.1.13. Replacement of the directing plug of the valve
      2.1.14. The valve
      2.1.15. A camshaft
      2.1.16. Rods
      2.1.17. A cranked shaft
      2.1.18. A flywheel
      2.1.19. A piston finger
      2.1.20. A final collector
      2.1.21. An inlet collector and the air chamber
      2.1.22. The block of cylinders
      2.1.23. Removal and engine and transmission installation
      2.1.24. System of release of the fulfilled gases
      2.1.25. Search and elimination of malfunctions
   + 2.2. Engines DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes


944881c0






2.1.5. A poliklinovoj belt Removal

PERFORMANCE ORDER
1. Ослабьте bolts of fastening of a pulley of the water pump.
2. Ослабьте nuts of support of the generator.
3. Ослабьте a bolt of fastening of the generator also remove поликлиновой a belt.
4. Turn out bolts of fastening of a pulley of the water pump.

The inhaling moment:
Sharnirnyj bolt () generator fastenings: 20-25 Н•м
Bolt () generator fastenings: 15-22 Н•м
Bolt of fastening of an arm of the generator: 20-28 Н•м


Check


Check up following elements and in the presence of defects replace them.

PERFORMANCE ORDER
1. Check up a surface поликлинового a belt on absence of damages and cracks.
2. Check up a surface поликлинового a belt on absence of oil and lubricant.
3. Check up a surface поликлинового a belt on absence of non-uniform deterioration.
4. Check up a pulley surface on absence of cracks or damages.

Installation

PERFORMANCE ORDER
1. Establish a pulley of the pump and fix its bolts.
2. After installation поликлинового a belt adjust its tension.

Check and tension adjustment

PERFORMANCE ORDER
1. Check up a condition поликлинового a belt and its arrangement on pulleys.

The prevention

Check up correctness of an arrangement of edges поликлинового a belt in flutes of pulleys.
If at work поликлиновой the belt publishes extraneous noise, check up a belt on absence of deterioration and damages, and also working surfaces of pulleys.


2. By the special device measure a tension of a belt of a drive of the generator. In the absence of the special device check up a belt tension, having pressed on it effort 100 Н (10 kg) in a place located on identical removal from pulleys and measure a belt deflection.

Tension of a belt of a drive of the generator:
New belt: 65-75 kg
The belt which was in the use: 40 kg
Check: 35-50 kg
Tension of a belt of a drive of the generator and the pump of the amplifier of a steering:
New belt: 55-70 kg
The belt which was in the use: 38-48 kg
Tension of a belt of a drive of the generator and the conditioner:
New belt: 60-70 kg
The belt which was in the use: 32-40 kg
Check: 25-50 kg

The belt which was in the use considers the belt which has worked on the engine more 5 minutes


Tension measurement by the special device of type And

PERFORMANCE ORDER
At tension measurement поликлинового a belt the device should not concern other elements of the engine.

At tension measurement поликлинового a belt the device should not concern other elements of the engine.

PERFORMANCE ORDER
1. At measurement be convinced that have turned the button of repeated installation in an arrow direction to establish an arrow of the device in an initial condition.
2. After removal of the device from a belt of the marksman of the device will still specify a belt tension.

The prevention

It is not recommended to regulate a belt tension by hand as this adjustment will not provide sufficient accuracy and the belt can slip on pulleys. Always use the special device.
Check up that the belt tension corresponds to demanded values.
Check a tension of a belt after a tightening шарнирного a bolt and a bolt of fastening of the generator.