Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
- 6. Fuel system
   6.1. Specifications (SOHC and DOHC)
   6.2. Check of the fuel pump
   6.3. Check of the pressure created by the fuel pump
   6.4. Checks of system of injection MFI
   6.5. A control lamp of malfunctions (MIL)
   6.6. Diagnostic codes of malfunctions ŤOBD-IIť
   6.7. Diagnostic codes of malfunctions, except ŤOBD-IIť
   6.8. Replacement of the fuel filter
   6.9. Replacement of the terminator of overflow (the double-thread valve)
   6.10. Replacement of the gauge of level of fuel
   6.11. A control system of engine MFI
   6.12. Fuel atomizers
   6.13. Throttle knot
   6.14. The power supply system with the carburettor
   6.15. Check of frequency of rotation of idling
   6.16. Adjustment of frequency of rotation of idling
   6.17. Frequency of rotation of idling and adjustment of a fuel mix
   6.18. Check and starting arrangement adjustment
   6.19. Check and adjustment of a free wheeling of a cable of an accelerator
   6.20. A fuel tank
   6.21. The canister of catching of steams of fuel
   6.22. Replacement of the fuel filter
   6.23. The carburettor
   6.24. A cable and an accelerator pedal
   6.25. Search and elimination of malfunctions of fuel system with the carburettor
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes


944881c0






6.5. A control lamp of malfunctions (MIL) Control lamp MIL lights up in the presence of malfunctions in a control system of the engine. However, lamp MIL will not light up after three starts of the engine if the malfunction fixed earlier does not appear any more. After ignition inclusion (before engine start) the control lamp burns constantly that specifies in normal work of system of diagnostics of malfunctions. The control lamp with system "OBD-II" lights up at occurrence of malfunctions in following elements of system:

каталитическом neutralizer;
– To fuel system;
– A measuring instrument of the expense of air;
– The gauge of temperature of air arriving in the engine;
– The gauge of temperature of a cooling liquid;
– The gauge of position throttle заслонки;
– The oxygen gauge;
– A heater of the gauge of oxygen;
– Fuel atomizers;
– Ignition admissions;
– The gauge of an angle of rotation of a cranked shaft;
– The gauge of position of a camshaft;
– To system of catching of steams of fuel;
– The gauge of speed of the car;
– The valve of adjustment of frequency of rotation of idling;
– An electric food;
ЕСМ;
– Infringement of functioning of a transmission;
– The acceleration gauge;
– Inquiry of signal MIL.


The control lamp without system "OBD-II" lights up at occurrence of malfunctions in following elements of system:

- The warmed gauge of oxygen;
- The gauge of absolute pressure in an inlet collector;
- The gauge of position throttle заслонки;
- The gauge of temperature of a cooling liquid;
- The modulator of management of frequency of rotation of a cranked shaft of the engine idling;
- Fuel atomizers;
- ЕСМ.

Check

PERFORMANCE ORDER
1. After ignition inclusion the control lamp lights up on 5 with then dies away.
2. If the control lamp does not light up, check up an electric chain of a lamp, integrity of a safety lock and serviceability of a lamp.

Self-diagnostics

Block ESM constantly supervises entrance both target signals and other signals under certain conditions. At failure detection block ESM writes down a diagnostic code of malfunction in memory and provides a code exit to a diagnostic socket. It is possible to consider diagnostic codes by means of control lamp MIL or scanner HI-SCAN. Diagnostic codes remain in memory to a detachment of wires from plugs of the storage battery or a detachment of a socket from block ESM, and also before their deleting by means of scanner HI-SCAN.
The prevention

If the socket is disconnected at the included ignition, in memory the code of malfunction DTC will be written down. In this case disconnect a wire from the negative plug of the storage battery for the period of more 15 with therefore diagnostic memory will be erased.