Hyundai Accent

Repair and car operation

12.17. The pump of the amplifier of a steering

1 – a bolt, 55–60 Н•м; 2 – a sealing ring of round section; 3 – a bolt, 16 Н•м; 4 – a soaking up pipe; 5 – the gauge of pressure of a liquid; 6 – a pulley; 7 – a lock ring; 8 – распорная the plug; 9 – a shaft with the bearing; 10 – a sealing ring; 11 – the case;

12 – a spring; 13 – an internal sealing ring; 14 – an external sealing ring; 15 – a forward lateral plate; 16 – blades; 17 – a rotor; 18 – a pin; 19 – статорное a ring; 20 – a lining; 21 – a back cover; 22 – a bolt, 38 Н•м.

Removal

---

The prevention

At service of the oil pump close the generator a polyethylene film.

---

PERFORMANCE ORDER

1. Disconnect a pressure head hose from the pump. 2. Disconnect soaking up filter from a socket всасывания and merge a liquid in the container. 3. Ослабьте bolts of fastening of the pump also remove приводной a belt. 4. Turn out assembly bolts of fastening of an arm of the pump and disconnect a socket of the gauge of pressure. 5. Remove the pump.

Dismantling

PERFORMANCE ORDER

1. Remove soaking up pipe and a sealing ring from the pump. 2. Remove a back cover with a lining and pins. 3. Remove статорное a ring. 4. Remove a rotor and blades. 5. Remove a forward lateral plate. 6. Remove internal and external sealing rings. 7. Remove a spring. The prevention At assemblage it is necessary to use a new lining and a sealing ring. 8. Turn away a nut of fastening of a pulley and remove a spring washer. 9. Remove a pulley and segment шпонку. 10. Using special flat-nose pliers, remove a lock ring. 11. Squeeze out a shaft of a pulley with the bearing. If necessary use a kapron hammer. 12. Remove a sealing ring from the pump case. The prevention At assemblage it is necessary to use a new sealing ring. 13. Remove an arm directing and turn away a nut. 14. Disconnect a socket from the case of the pump and remove a throttle and a spring. 15. Remove a sealing ring from a socket. The prevention Do not make throttle dismantling.

Check

PERFORMANCE ORDER

1. Clear all details of the pump corresponding solvent. 2. If there are damaged details of the pump, replace the pump in gathering. 3. If the pulley is damaged or deformed, replace it. 4. If there are leaks of a liquid about a sealing ring, replace it. 5. If are damaged or worn out шлицы a shaft or a pulley, replace corresponding details.

Assemblage

PERFORMANCE ORDER

1. Establish the pump switch. 2. Establish a throttle spring, the valve and a socket in the pump case. The prevention Grease with a thin layer of liquid ATF DEXRON II all replaced details, including oil consolidation and a sealing ring. 3. Establish an arm directing and screw nuts. 4. The special tool 09222–32100 establish oil consolidation in the pump case. 5. Softly insert assemblage of a shaft and establish a lock ring. 6. Establish a pulley of the pump with segment шпонкой. 7. Establish a spring both internal and external sealing rings. 8. Establish a forward lateral plate. 9. Insert pins into deepenings of the forward case, then establish статорное a ring, paying attention to a direction of its installation. 10. Establish a rotor so that labels on a rotor settled down from outside, an opposite forward part of the case. 11. Establish blades the rounded off parts outside. 12. Establish a lining and a back cover. 13. Tighten a socket всасывания.

Installation

PERFORMANCE ORDER

1. Establish the pump to a pump arm. 2. Establish soaking up filter. 3. Establish поликлиновой a belt and adjust its tension. 4. Connect a pressure head hose to the pump and the soaking up filter with a tank. The prevention Establish hoses so that they have not been overwound and did not make contact with any other parts. 5. Fill in a liquid. The recommended liquid: PSF–3 6. Pump over a hydraulic drive of the amplifier of a steering. 7. Check up the pressure created by the pump.