Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
- 13. Brake system
   13.1. Specifications
   13.2. Antiblocking system of brakes (ABS)
   13.3. Prorolling of hydraulic system of a drive of brakes with scanner use
   13.4. Check and adjustment of position of a pedal of a brake
   13.5. Check of the vacuum amplifier of brakes
   13.6. Prorolling of hydraulic system of a drive of brakes
   13.7. Adjustment of a course of a lay brake
   13.8. The vacuum amplifier of brakes
   13.9. Brake tubes and hoses
   13.10. A pressure regulator
   13.11. A brake pedal
   13.12. Replacement of lobbies brake колодок
   13.13. A support of a forward brake
   13.14. The main brake cylinder
   13.15. Replacement brake колодок on back drum-type brakes
   13.16. Replacement of the working brake cylinder
   13.17. A lay brake
   13.18. Hydraulic block HECU ABS
   13.19. The gauge of frequency of rotation of a wheel
   13.20. Search and elimination of malfunctions
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes


944881c0






13.12. Replacement of lobbies brake колодок

Support of a forward brake

1 – brake колодка;
2 – a dustproof cover;
3 – the piston;
4 – a sealing ring;
5 – a support with the cylinder;
6 – a protective cover;
7 – a plug bolt, 22–32 Н•м;
8 – the prorolling union;
9 – a dustproof cap;
10 – a hollow bolt, 25–30 Н•м;
11 – a brake hose;
12 – a washer;
13 – a protective cover;
14 – a directing finger, 35–45 Н•м;
15 – a bolt of fastening of a support, 65–75 Н•м;
16 – a fixing element;
17 – the plug;
18 – a protective cover;
19 – a lining;
20 – a spring;
21 – a lining.

Removal

PERFORMANCE ORDER
1. Turn out lower bolt, lift a support upwards and fix its wire.
2. Remove brake колодки.

The prevention

Do not press a pedal of a brake after removal brake колодок.



Check


PERFORMANCE ORDER
1. Check up brake колодки on absence of deterioration or pollution by oil and, if necessary, replace them.

Thickness of overlays brake колодок:
The nominal: 90 mm
Is minimum admissible: 2,0 mm

The prevention

Necessarily replace all колодки on one axis of the car even if one is worn out only колодка. If brake колодки will be repeatedly established, before removal they are necessary for marking.


2. Check up overlays brake колодок on absence of damages.

Installation

PERFORMANCE ORDER
1. Establish clips brake колодок.
2. Establish brake колодки on each clip brake колодок.

The prevention

Brake колодку with the deterioration gauge establish from outside the piston.


3. The special tool 09581–11000 press the piston into the support cylinder.
4. Establish new brake колодки.

The prevention

Never put greasing on a brake disk and brake колодки.


5. Screw a bolt and tighten its demanded moment.

The inhaling moment: 22–32 Н•м