Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
- 13. Brake system
   13.1. Specifications
   13.2. Antiblocking system of brakes (ABS)
   13.3. Prorolling of hydraulic system of a drive of brakes with scanner use
   13.4. Check and adjustment of position of a pedal of a brake
   13.5. Check of the vacuum amplifier of brakes
   13.6. Prorolling of hydraulic system of a drive of brakes
   13.7. Adjustment of a course of a lay brake
   13.8. The vacuum amplifier of brakes
   13.9. Brake tubes and hoses
   13.10. A pressure regulator
   13.11. A brake pedal
   13.12. Replacement of lobbies brake колодок
   13.13. A support of a forward brake
   13.14. The main brake cylinder
   13.15. Replacement brake колодок on back drum-type brakes
   13.16. Replacement of the working brake cylinder
   13.17. A lay brake
   13.18. Hydraulic block HECU ABS
   13.19. The gauge of frequency of rotation of a wheel
   13.20. Search and elimination of malfunctions
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes


944881c0






13.13. A support of a forward brake Removal

PERFORMANCE ORDER
1. Remove a forward wheel.
2. Turn out a hollow bolt and disconnect from a support a brake hose.

The prevention

For an exception вытекания a brake liquid close an aperture in a brake hose a suitable stopper.


3. Turn out bolts of fastening of a support.
4. Remove a support and brake колодки.
5. Turn out bolts of fastening of the holder of a support (2EA) to a rotary fist.
6. Remove a fixing element of a support.

Dismantling

PERFORMANCE ORDER
1. Remove a dustproof cover of the piston.
2. Compressed air squeeze out the piston from the support cylinder.

The prevention

At piston expression by the compressed air have no fingers in front of the piston.
Be careful, as from the channel the compressed air together with the piston blows a brake liquid.


3. A screw-driver edge remove a sealing ring from the piston.

Check

PERFORMANCE ORDER
1. Check up a support on absence of deterioration, damages, cracks and a rust.
2. Check up the piston on absence of a rust, damages, cracks and deterioration of an external surface.
3. Check up the plug and directing finger on absence of damages and a rust.
4. Check up a spring and covers on absence of damages.
5. Check up a fixing element on absence of deterioration, damages, cracks and a rust.

The prevention

Do not use an emery paper for clearing of a surface of the piston.
It is necessary to replace all rubber details with the new.


6. Measure a thickness of a brake disk. By the indicator of hour type measure palpation of a brake disk on small distance from external edge.

Thickness of a brake disk:
The nominal: 19 mm
Is minimum admissible: 17 mm
Maximum permissible palpation: 0,05 mm.

7. If necessary, replace a brake disk.


Assemblage

PERFORMANCE ORDER
1. Clear all details, except for brake колодок, изопропиловым spirit.
2. Put special greasing on a sealing ring of the piston and establish it in a piston flute.
3. Collect the piston and piston covers in a following order:

– Put special greasing on walls of the cylinder of a support, an external surface of the piston and a piston cover;
– Establish a piston cover how it is shown in drawing;
– Insert a piston cover into an internal flute of a support and move the piston into a support.
4. Collect mobile details in a following order:

– Put special greasing on an external surface of the plug, directing finger and in an aperture for the plug and establish protective covers;
– Insert covers into support flutes.
5. Establish brake колодки.

The prevention

Never put greasing on a brake disk and brake колодки.


6. Screw and tighten the demanded moment of an inhaling a hollow bolt of fastening of a brake hose.

The inhaling moments:
Directing finger: 34–44 Н•м
Sliding bolt: 22–31 Н•м
Bolt of a fixing element of a support: 64–74 Н•м
Hollow bolt of fastening of a brake hose: 25–29 Н•м


The prevention

Before installation check up that surfaces of bolts and a directing finger are not damaged.
Remove air from a hydraulic drive of brake system. Some times press a pedal of a brake and check up absence of leak of a brake liquid.