Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
- 13. Brake system
   13.1. Specifications
   13.2. Antiblocking system of brakes (ABS)
   13.3. Prorolling of hydraulic system of a drive of brakes with scanner use
   13.4. Check and adjustment of position of a pedal of a brake
   13.5. Check of the vacuum amplifier of brakes
   13.6. Prorolling of hydraulic system of a drive of brakes
   13.7. Adjustment of a course of a lay brake
   13.8. The vacuum amplifier of brakes
   13.9. Brake tubes and hoses
   13.10. A pressure regulator
   13.11. A brake pedal
   13.12. Replacement of lobbies brake колодок
   13.13. A support of a forward brake
   13.14. The main brake cylinder
   13.15. Replacement brake колодок on back drum-type brakes
   13.16. Replacement of the working brake cylinder
   13.17. A lay brake
   13.18. Hydraulic block HECU ABS
   13.19. The gauge of frequency of rotation of a wheel
   13.20. Search and elimination of malfunctions
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes


944881c0






13.15. Replacement brake колодок on back drum-type brakes

Brake колодки on back drum-type brakes

1 – a rack of support brake колодок;
2 – a brake board;
3 – the working brake cylinder;
4 – a lever latch;
5 – разжимная a lath;
6 – the lever of a lay brake;
7 – the top returnable spring;
8 – back brake колодка;
9 – a spring;
10 – a clip;
11 – a brake drum;
12 – the bottom returnable spring;
13 – a regulator spring;
14 – a lobby brake колодка.

Removal

PERFORMANCE ORDER
1. Remove a wheel and a brake drum.
2. Remove a clip of support brake колодки, a spring of an automatic regulator and the regulator lever.
3. Press колодки and remove a regulator колодок.
4. Remove brake колодки together with returnable springs.

Check

PERFORMANCE ORDER
1. Measure internal diameter of a brake drum. The indicator of hour type check up palpation of a brake drum. Replace a brake drum if internal diameter of a drum exceeds maximum permissible value.

The maximum diameter: 200 mm
Palpation of a brake drum: 0,015 mm

2. Measure a thickness of overlays back brake колодок. Replace all brake колодки on one axis of the car even if only one колодка has a thickness, smaller maximum permissible.

Is minimum admissible thickness: 1,0 mm

3. Check up overlays brake колодок on absence of pollution by oil or lubricants, deterioration and cracks.
4. Examine working brake cylinders on absence of leaks of a brake liquid.
5. Examine a brake board on absence of deterioration or damages.
6. Check up uniformity прилегания brake колодки to a brake drum.

Installation

PERFORMANCE ORDER
1. With greasing grease following points of contact brake колодок:
a. Points of contact brake колодок with a brake board;
b. Points of contact brake колодок with a basic plate.

The recommended lubricant: SAE J310, NLGI №2

2. Establish a rack of support brake колодки.
3. Establish returnable springs on brake колодки.
4. After installation of a brake drum some times tighten the lever of a lay brake.