Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
- 15. A central air
   15.1. Specifications
   15.2. The instruction on coolant application
   15.3. Remarks at replacement of elements of a central air of air
   15.4. Connection of elements of a central air of air
   15.5. Check of elements of the central air established on the car
   15.6. Installation of manometres for pressure measurement
   15.7. Откачка atmospheric air from a central air
   15.8. Gymnastics of a central air of air
   15.9. Check of level of a coolant
   15.10. Check of operational characteristics
   15.11. Oil for greasing of the compressor of the conditioner
   15.12. Relay check
   15.13. The conditioner compressor
   15.14. The plug of coupling and a pulley of the compressor of the conditioner
   15.15. The coil of excitation of coupling
   15.16. Compressor check on the car
   15.17. The gauge of threefold (double) pressure
   15.18. The fan and the condenser
   15.19. The evaporator
   15.20. Check of the thermostatic gauge (термистора)
   15.21. The air filter of the evaporator
   15.22. The heating and ventilation block
   15.23. The heater block
   15.24. The fan
   15.25. Search and elimination of malfunctions
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes


944881c0






15.18. The fan and the condenser
1 – a condenser tank;
2 – the condenser fan;
3 – a bolt of fastening of the fan of the condenser;
4 – the condenser.

Removal

PERFORMANCE ORDER
1. Discharge air central air.
2. Merge cooling liquid from a radiator.
3. Turn out two bolts of the top fastening of clips of a radiator and the air inlet pipeline.
4. Remove two clips and the air inlet pipeline.
5. Disconnect from a radiator entrance and target hoses.
6. Disconnect hoses from an oil radiator of a transmission.
7. Disconnect sockets from the fan of a radiator and the condenser fan.
8. Remove in gathering a radiator and the condenser.
9. Disconnect from the condenser an exhaust pipe and a tube for a coolant.

The prevention

After separation of components of a central air of air immediately close connections by corresponding covers for an exception of hit of a moisture of air in system.
Be careful not to damage an exhaust pipe and a tube for a coolant.
Be careful not to damage a condenser plate.


10. Turn out two bolts of fastening of the condenser.
11. Remove the condenser.

Check of the fan of the condenser

PERFORMANCE ORDER
1. Check up work of the fan of the condenser.
2. Check up a condition of an electric socket of a plait of wires.
3. The fan engine rotates at giving of pressure 12 In on contacts of a socket of the engine of the fan.

Installation

PERFORMANCE ORDER
1. Installation is spent to sequences, return to removal.
2. If condenser replacement was spent, add in the compressor of oil of 25 sm3.
3. Pump out, charge and check up air central air.

Condenser check on the car

PERFORMANCE ORDER
1. Check up condenser plates on absence of a contamination and damage. If plates are hammered, wash out their stream at its finest and blow compressed air. If погнуты plates, level them пассатижами and a screw-driver.
2. Check up places of connection of the condenser on absence of leaks.