Hyundai Accent

Repair and car operation


Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
- 15. A central air
   15.1. Specifications
   15.2. The instruction on coolant application
   15.3. Remarks at replacement of elements of a central air of air
   15.4. Connection of elements of a central air of air
   15.5. Check of elements of the central air established on the car
   15.6. Installation of manometres for pressure measurement
   15.7. Откачка atmospheric air from a central air
   15.8. Gymnastics of a central air of air
   15.9. Check of level of a coolant
   15.10. Check of operational characteristics
   15.11. Oil for greasing of the compressor of the conditioner
   15.12. Relay check
   15.13. The conditioner compressor
   15.14. The plug of coupling and a pulley of the compressor of the conditioner
   15.15. The coil of excitation of coupling
   15.16. Compressor check on the car
   15.17. The gauge of threefold (double) pressure
   15.18. The fan and the condenser
   15.19. The evaporator
   15.20. Check of the thermostatic gauge (термистора)
   15.21. The air filter of the evaporator
   15.22. The heating and ventilation block
   15.23. The heater block
   15.24. The fan
   15.25. Search and elimination of malfunctions
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

944881c0





15.19. The evaporator
1 – the air filter;
2 – a cover of the air filter;
3 – top картер the evaporator; 		4 – an evaporator radiator;
5 – bottom картер the evaporator.

Removal
PERFORMANCE ORDER
1. Disconnect a wire from the negative plug of the storage battery.
2. Discharge air central air.
3. Disconnect a tube () and the soaking up filter from the evaporator.
The prevention

After separation of components of a central air of air immediately close connections by corresponding covers for an exception of hit of a moisture of air in system.
4. Disconnect a hose of a drain from the evaporator.
5. Turn out two screws and uncover a condensing ring from the panel of devices.
6. Turn out three screws of fastening of a ware box.
7. Disconnect a socket from the thermostatic switch.
8. Turn out three screws of fastening of the evaporator.
9. Remove the evaporator.

Dismantling

PERFORMANCE ORDER
1. Remove 7 clips of fastening top картера the evaporator.
2. Remove top картер the evaporator.
The prevention

Be careful not to damage electroconducting of the thermostatic switch.
3. Remove the thermostatic switch with the thermoresistor and its clip from the evaporator block.
4. Remove the evaporator.

Check
PERFORMANCE ORDER
1. Check up evaporator plates on absence of a contamination and damage. If plates are hammered, blow their compressed air.
The prevention

Do not use water for clearing of plates of the evaporator.
2. Check up joints at absence of cracks and scratches.

Assemblage
PERFORMANCE ORDER
1. Establish the evaporator in bottom картер.
2. Establish the thermostatic switch with the thermoresistor to the evaporator.
3. Establish top картер.
4. Establish seven clips and screw two screws.

Installation
PERFORMANCE ORDER
1. Installation is spent to sequences, return to removal.
2. If evaporator replacement was spent, add in the compressor of oil of 40 sm3.
3. Pump out, charge and check up air central air.

Check on the car
PERFORMANCE ORDER
1. Check up quantity of a coolant during a cooling cycle.
2. Establish manometres on a highway.
3. Start the engine, leave to work on 5 mines on frequency of rotation of a cranked shaft of 2000 mines-1.
4. Check up the evaporator on presence of following defects:

– If the broad valve is hammered, the indication of a manometre of low pressure will decrease to 0kg/sm2;
– If the broad valve is hammered or there are leaks in the evaporator, repair or replace the evaporator.