Hyundai Accent

Repair and car operation


Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
- 9. A transmission
   + 9.1. A mechanical transmission
   - 9.2. An automatic transmission
      9.2.1. Specifications
      9.2.2. A control lamp of malfunctions (MIL)
      9.2.3. Diagnostic codes of malfunctions
      9.2.4. Reading of codes of malfunctions
      9.2.5. Pressure check трансмиссионной liquids
      9.2.6. Testing of teamwork of an automatic transmission and the engine for the motionless car (stall test)
      9.2.7. Check of level of a liquid in an automatic transmission
      9.2.8. Check of work of the lever of the selector
      9.2.9. Adjustment of the switch of indication of position of the lever of the selector
      9.2.10. Adjustment of the servo-driver of compulsory inclusion of a hill-climbing gear
      9.2.11. Pressure adjustment in a highway
      9.2.12. Replacement of an oil sealing ring of a power shaft
      9.2.13. Replacement of a cable of a drive of a speedometer
      9.2.14. Removal and transmission installation
      9.2.15. Transmission repair
      9.2.16. The selector lever
      9.2.17. Adjustment of a cable of management
      9.2.18. Repair of the lever of the selector
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

Сантехнические перегородки
944881c0





9.2.14. Removal and transmission installation Removal
PERFORMANCE ORDER
1. Disconnect, first of all, a wire from the negative plug of the storage battery, then - from positive. Turn out a drain stopper and merge in suitable capacity трансмиссионное oil from a transmission.
2. Remove the case of the air filter.
3. Ослабьте collars also disconnect giving and return hoses трансмиссионной liquids to a radiator.
The prevention

For a hit exception in a dirt and dust transmission close apertures suitable stoppers.

4. Remove a cable of management of a transmission.
5. Remove a cable of a drive of a speedometer.
6. Disconnect electric sockets from the generator of impulses, the switch of ranges of a transmission, the switch of the servo-driver of compulsory inclusion of a hill-climbing gear, the electromagnetic valve and the temperature gauge трансмиссионной liquids.
7. Turn out bolts of fastening of the top part of a transmission to the engine.
8. The special adaptation support the engine so that the engine weight was perceived by the adaptation.
9. Disconnect the stabilizer of cross-section stability, connecting draught, the spherical hinge of the bottom lever and power shafts.
10. Turn out connecting шарнирные bolts of a transmission and assembly bolts of fastening of returnable pipes.
11. Turn out bolts and remove the bottom frame.
12. Remove a starter.
13. Turn out bolts of fastening of a transmission.
14. Take away a transmission from the engine.
15. Remove a transmission from the car.
The prevention

At transmission installation it is necessary to observe sequence of installation of arms.

1) the Arm of support of the engine.
2) the Top arm of a transmission.
3) the Back arm.
4) the Forward arm.


Installation
PERFORMANCE ORDER
Establish on a forward part of a transmission the hydrotransformer and establish a transmission to the engine.
The prevention

If the hydrotransformer to establish at first on the engine, at transmission installation the sealing ring of a transmission can be damaged.