Hyundai Accent

Repair and car operation

Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
- 9. A transmission
   + 9.1. A mechanical transmission
   - 9.2. An automatic transmission
      9.2.1. Specifications
      9.2.2. A control lamp of malfunctions (MIL)
      9.2.3. Diagnostic codes of malfunctions
      9.2.4. Reading of codes of malfunctions
      9.2.5. Pressure check трансмиссионной liquids
      9.2.6. Testing of teamwork of an automatic transmission and the engine for the motionless car (stall test)
      9.2.7. Check of level of a liquid in an automatic transmission
      9.2.8. Check of work of the lever of the selector
      9.2.9. Adjustment of the switch of indication of position of the lever of the selector
      9.2.10. Adjustment of the servo-driver of compulsory inclusion of a hill-climbing gear
      9.2.11. Pressure adjustment in a highway
      9.2.12. Replacement of an oil sealing ring of a power shaft
      9.2.13. Replacement of a cable of a drive of a speedometer
      9.2.14. Removal and transmission installation
      9.2.15. Transmission repair
      9.2.16. The selector lever
      9.2.17. Adjustment of a cable of management
      9.2.18. Repair of the lever of the selector
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

9.2.6. Testing of teamwork of an automatic transmission and the engine for the motionless car (stall test) Testing is carried out to define, whether is available проскальзывание elements of a friction or infringement in work of hydraulic components.
The prevention
At performance of testing nobody should stand ahead and behind the car.

PERFORMANCE ORDER

1. Before testing check up levels of all operational liquids and, if necessary, finish them to the normal. The temperature трансмиссионной liquids should be in limits 80–90°С, and a cooling liquid 80–90°C.

2. Establish клиновые an emphasis under forward and back wheels.

3. Connect to the engine a tachometre.

4. Tighten a lay brake and press a brake pedal.

5. Start the engine.

6. Move the selector lever to a position "D". The left foot press against the stop a brake pedal, and the right foot smoothly press an accelerator pedal. When frequency of rotation of a cranked shaft of the engine does not increase any more, read indications of a tachometre and release an accelerator pedal. For an exception of damage of a transmission testing spend during 5 with. If it is necessary to spend more than one testing at the working engine move the selector lever to position N and leave the engine to work on frequency of rotation of idling within 2 minutes engine Work on frequency of rotation of idling cools трансмиссионную a liquid and prevents deterioration of its properties.
Frequency of rotation of a cranked shaft of the engine at testing of teamwork of an automatic transmission and the engine for the motionless car (stall test): 2300–2700 mines-¹.

7. Similarly hold testing in position "R" the selector lever.

If frequency of rotation of a cranked shaft of the engine above the specification in position D, means, pressure трансмиссионной is not enough liquid as a result of leak in back coupling or обгонной муфте.

If frequency of rotation of a cranked shaft of the engine above the specification in position R, means, pressure трансмиссионной is not enough liquid as a result of leak in forward coupling or a brake tape of forward bottom transfers and a backing.

If frequency of rotation of a cranked shaft of the engine below the specification in position D, means, pressure трансмиссионной is not enough liquid as a result of deterioration of the oil pump or malfunction of the hydrotransformer.