Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
- 9. A transmission
   + 9.1. A mechanical transmission
   - 9.2. An automatic transmission
      9.2.1. Specifications
      9.2.2. A control lamp of malfunctions (MIL)
      9.2.3. Diagnostic codes of malfunctions
      9.2.4. Reading of codes of malfunctions
      9.2.5. Pressure check трансмиссионной liquids
      9.2.6. Testing of teamwork of an automatic transmission and the engine for the motionless car (stall test)
      9.2.7. Check of level of a liquid in an automatic transmission
      9.2.8. Check of work of the lever of the selector
      9.2.9. Adjustment of the switch of indication of position of the lever of the selector
      9.2.10. Adjustment of the servo-driver of compulsory inclusion of a hill-climbing gear
      9.2.11. Pressure adjustment in a highway
      9.2.12. Replacement of an oil sealing ring of a power shaft
      9.2.13. Replacement of a cable of a drive of a speedometer
      9.2.14. Removal and transmission installation
      9.2.15. Transmission repair
      9.2.16. The selector lever
      9.2.17. Adjustment of a cable of management
      9.2.18. Repair of the lever of the selector
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes


944881c0






9.2.5. Pressure check трансмиссионной liquids

Arrangement of sealing rings

1 – an oil sealing ring;
2 – a sealing ring;
3 – a sealing ring of D-shaped section;
4 – a sealing ring of D-shaped section;
5 – a sealing ring of D-shaped section;
6 – an oil sealing ring;
7 – a sealing ring;
8 – a sealing ring of D-shaped section.

Pressure check трансмиссионной liquids is carried out to define a condition of hydraulic components and whether there are leaks.

PERFORMANCE ORDER
1. Start up the engine before warming up of a transmission to temperature 60~70°C.
2. Lift the forward party of the car so that driving wheels could rotate freely.
3. Connect a tachometre and arrange so that it was well visible.
4. Connect a special manometre 09452–21500 with an adapter 09452–21002 to each union of check of pressure.

For check of return pressure it is necessary to use a manometre with a limit of measurement 3 000 кПа.
5. Measure pressure трансмиссионной liquids at various positions of the lever of the selector and frequency of rotation of a cranked shaft of the engine. If pressure does not correspond to demanded values, check up and repair transmission elements.

Condition Standard pressure трансмиссионной liquids, кПа
Selector positions Speed of km/h Frequency of rotation of a cranked shaft Position of the lever of the selector Pressure reduction Kickdown Forward coupling Pressure of coupling Brakes of low transfers and З.Х. Pressure of a regulator of coupling Pressure of a regulator демпфера couplings Back coupling
1 N 0 Х.Х. Нейтрал. 430±30
2 D 0 Х.Х. 2nd lane 430±30 138–277
3 D (SW–ON) 110 2500 4th lane 430±30 840–900 650–710 570–630 840–900
4 D (SW–OFF) 75 2500 3rd lane 430±30 840–900 840–900 840–900 680–820 840–900
5 2 50 2500 2nd lane 430±30 840–900 490–785 840–900
6 L 0 2500 1st lane 430±30 500–630 530–630 840–900
7 R 35 2500 З.х. 420–480 500–700
0 1000 450