Hyundai Accent

Repair and car operation

Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
- 9. A transmission
   + 9.1. A mechanical transmission
   - 9.2. An automatic transmission
      9.2.1. Specifications
      9.2.2. A control lamp of malfunctions (MIL)
      9.2.3. Diagnostic codes of malfunctions
      9.2.4. Reading of codes of malfunctions
      9.2.5. Pressure check трансмиссионной liquids
      9.2.6. Testing of teamwork of an automatic transmission and the engine for the motionless car (stall test)
      9.2.7. Check of level of a liquid in an automatic transmission
      9.2.8. Check of work of the lever of the selector
      9.2.9. Adjustment of the switch of indication of position of the lever of the selector
      9.2.10. Adjustment of the servo-driver of compulsory inclusion of a hill-climbing gear
      9.2.11. Pressure adjustment in a highway
      9.2.12. Replacement of an oil sealing ring of a power shaft
      9.2.13. Replacement of a cable of a drive of a speedometer
      9.2.14. Removal and transmission installation
      9.2.15. Transmission repair
      9.2.16. The selector lever
      9.2.17. Adjustment of a cable of management
      9.2.18. Repair of the lever of the selector
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

9.2.16. The selector lever

1 – a cable of management of a transmission;
2 – a nut;
3 – the solenoid of the lock of blocking;
4 – a wire and a lamp of illumination of the control panel a transmission;
5 – O/D the switch;
6 – the button;
7 – the handle; 8 – the control panel a transmission;
9 – an adjusting cam of the lever;
10 – the selector lever;
11 – the switch of neutral position of a transmission;
12 – an arm;
13 – a connecting tip of a cable.

Removal

PERFORMANCE ORDER

1. Remove the central console.

2. Turn out screws of fastening of the handle of the lever of the selector.

3. Disconnect a socket of the switch of an overdrive gear, get three contacts from a socket and remove the handle from the lever.

4. Disconnect a socket of a lamp of illumination of the control panel a transmission.

5. Remove the control panel a transmission.

6. Remove a clip of fastening of draught.

7. Remove a clip from outside the selector lever.

8. Turn out bolts and remove washers of fastening of a cable under the panel of devices.

9. Remove a clip of fastening of a cable from outside transmissions.

10. Remove a cable of management of a transmission.

Check

PERFORMANCE ORDER

1. Check up functioning of a cable of management by a transmission and absence of damages.

2. Check up the plug on absence of deterioration or damages.

3. Check up a spring on absence of damages and elasticity loss.

4. Check up conductivity of the switch of an overdrive gear. At activation of an overdrive gear contacts 1 and 2 switches should be closed, and at деактивировании contacts 1 and 3 should be closed.

Installation

PERFORMANCE ORDER

1. Grease an internal part of the plug.
Greasing: SAE J310, NLGI №0

2. Move the lever of the selector and the switch of a range of a transmission to position N and connect a management cable.

3. At connection of a cable of management by a transmission move a cable arm while the cable will not be combined with the transmission lever.

4. Establish a washer and screw a bolt and a nut of fastening of a cable.

5. From outside the selector lever establish a clip.

6. Connect a socket of a lamp of illumination of the indicator of position of the lever of the selector, switch O/D socket, a socket of the switch of a parking and a socket of a choice of a mode of movement.

7. Establish the control panel a transmission.

8. Put greasing in a place shown in drawing.
Greasing: SAE J310, NLGI №2

9. Establish the selector lever in position N, then turn a cam overlay so that the backlash between an overlay of a cam and knot corresponded to demanded value.
Backlash: 15,2–15,9 mm

The prevention
Be convinced that the party In an adjusting cam of the lever settled down from outside buttons.

10. Establish switch O/D on the lever handle, then insert contacts into a switch socket.

11. Establish the handle of the lever and fix its two screws.

12. Establish the central console.